ESCUDO TANQUE COMBUSTIBLE

1941 - 1945, Preguntas y discuciones tecnicas y todo lo relacionado con los jeep de la WWII.

Moderador: administrador

ESCUDO TANQUE COMBUSTIBLE

Notapor luisal1945 » 02 Nov 2015, 20:08

Imagen

Amigos del foto, necesito colocar el escudo del tanque de combustible (cuya foto adjunto) a mi Willys MB.
Entiendo que, entre el piso del Jeep y el escudo va una madera, a la cual tendría que fabricar.
No tengo referencias de las medidas de la madera en cuestión.
Alguien podria facilitarme esa información ?
Desde ya gracias.
Luis
Luis Alvira
Socio n° 146
Avatar de Usuario
luisal1945
 
Mensajes: 634
Registrado: 23 Ago 2015, 08:39
Ubicación: Guadalupe Norte (Ruta Nac 11 km 814), prov de Santa Fe
Gracias dadas: 0
Gracias recibidas: 51

Re: ESCUDO TANQUE COMBUSTIBLE

Notapor m606paz » 02 Nov 2015, 20:21

Hola Luis

Jon escribió:
To answer the question...
The wood spacer is made of Oak..1/4" thick.....x 3/4" wide....x 13.250" long
Drilled are three holes at 6" spacings.
Go get your measuring stick, if your length of the fold is 3.250" you need the spacer, if your fold is 3.500". you probably don't need it.
The piece is listed as "Shield, Fuel Tank", it's there to keep crap out of the fuel tank area.The wood spacer is listed as Part No. W-O A-3248 I have never been able to find a Ford part number for the spacer, yet, I have seen Ford seats require the spacer to allow the three holes to align with the captive nuts in the rear floor. My "F" marked seat for the '44 GPW needs it.
Several shapes of the final fold (the one with the three holes to align with the captive nuts and wood spacer holes), some have been noted as having straight cut ends, while Fords in particular have rounder ends.
Some are merely spot welded to the seat pan, others are seen with spot welds and attaching machine thread screws.

All the wood does is bridge the gap between the Shield and the floor so the holes align.

Imagen



http://g503.com/forums/viewtopic.php?t=117756
Mariano Paz
Socio n°27
1944 Ariel WNG
1945 Ford FAT
LU4ALM
Avatar de Usuario
m606paz
 
Mensajes: 16501
Registrado: 16 Abr 2009, 17:33
Ubicación: Berazategui, Buenos Aires
Gracias dadas: 1277
Gracias recibidas: 472

Re: ESCUDO TANQUE COMBUSTIBLE

Notapor vladimirsinisi » 02 Nov 2015, 21:46

creo que entre MB y GPW habia una diferencia, una llevaba madera y otro no pero no recuerdo como era :x
Vladimir Sinisi
Socio n° 136
☆ GPW <>139284 ☆
Trailer M100 #216
vladimirsinisi
 
Mensajes: 3954
Registrado: 14 Feb 2011, 18:40
Ubicación: LA PLATA
Gracias dadas: 84
Gracias recibidas: 142

Re: ESCUDO TANQUE COMBUSTIBLE

Notapor charlie s. » 03 Nov 2015, 11:46

El MB Slat lleva la madera.
Imagen
Slds
Charlie S.
MB Slat Grill 1942
CJ2A 1947
Spen Trailer 1948
Avatar de Usuario
charlie s.
 
Mensajes: 1532
Registrado: 06 May 2009, 10:55
Ubicación: Capital Federal
Gracias dadas: 41
Gracias recibidas: 65

Re: ESCUDO TANQUE COMBUSTIBLE

Notapor m606paz » 03 Nov 2015, 14:56

despues voy a buscar el manual de partes... :roll:

Imagen


buscando me encontre con este post viejo aqui en el foro viewtopic.php?f=4&t=1244&p=51818#p51818
Mariano Paz
Socio n°27
1944 Ariel WNG
1945 Ford FAT
LU4ALM
Avatar de Usuario
m606paz
 
Mensajes: 16501
Registrado: 16 Abr 2009, 17:33
Ubicación: Berazategui, Buenos Aires
Gracias dadas: 1277
Gracias recibidas: 472


Volver a Bantam BRC , Willys MA, Ford GP, Willys MB, Ford GPW, Informacion Tecnica

¿Quién está conectado?

Usuarios navegando por este Foro: No hay usuarios registrados visitando el Foro y 7 invitados

cron