Muy facil de hacer y no romperse los dedos

Fabricantes, configuraciones, palas, hachas, picos ,cabrestantes, aceiteras, graseras, otros.

Moderador: administrador

Muy facil de hacer y no romperse los dedos

Notapor pascualmattera » 15 Dic 2013, 20:44

interesante y facil de hacer

garys escribió:There seems to be quite a number of posts regarding "How Do I Install Split Rivets?" Split rivets are the little split legged solid rivets that are used primarily to hold in place the grille welting.

The proper size split rivet for this application is a 9/16" tall rivet with a 9/64" solid shank. Unfortunately, this is not a commonly stocked size and the substitute that has been furnished with the numerous reproduction welting kits is a 1/2" OAL rivet with a longer 3/16" solid shank. This longer shank plays havoc for those installing the rivets improperly. Rivets that are peened or folded over forming a 90 degree angle to the back of the grille, will inevitably be loose fitting.

Although the shorter rivets are an easier installation, the longer rivets will work quite well if you install them as they were designed with a "rolled leg".
This rolled leg should extend upwards past the solid "crotch" of the rivet and will take up any clearance. This roll-forming also pre-loads the rivet so it will remain tight.

The following photos illustrate a hand built roll forming anvil that was welded onto the jaws of a inexpensive pair of "vise grip" pliers.
Imagen

Imagen

Imagen

Imagen

There are 19 rivets required to fasten the welting kits. My kit came with exactly 19 rivets....not much margin for error.

If you install a "jam nut" on the adjustable lever of the vise grips you can consistantly control the rivet forming length.

http://g503.com/forums/viewtopic.php?t=80626
saludos
Pascual
Socio n° 66
m38a1
m151a2
m416 trailer 1/4 ton
m762 trailer 3/4 ton
m105a2 trailer 1.5 ton
ar100 trailer en recuperacion
Operador CW LW4DXL
Avatar de Usuario
pascualmattera
 
Mensajes: 1301
Registrado: 11 May 2009, 19:30
Ubicación: Quilmes, Buenos Aires
Gracias dadas: 0
Gracias recibidas: 81

Re: Muy facil de hacer y no romperse los dedos

Notapor m606paz » 15 Dic 2013, 21:03

Mañana te la fabricas Pascual? :D
Mariano Paz
Socio n°27
1944 Ariel WNG
1945 Ford FAT
LU4ALM
Avatar de Usuario
m606paz
 
Mensajes: 16501
Registrado: 16 Abr 2009, 17:33
Ubicación: Berazategui, Buenos Aires
Gracias dadas: 1277
Gracias recibidas: 472

Re: Muy facil de hacer y no romperse los dedos

Notapor vladimirsinisi » 15 Dic 2013, 22:16

ese tipo de remaches para que se usan? :roll:
Mariano yo creo que Pascual ya se la hizo :wink:
Vladimir Sinisi
Socio n° 136
☆ GPW <>139284 ☆
Trailer M100 #216
vladimirsinisi
 
Mensajes: 3954
Registrado: 14 Feb 2011, 18:40
Ubicación: LA PLATA
Gracias dadas: 84
Gracias recibidas: 142

Re: Muy facil de hacer y no romperse los dedos

Notapor ecn1960 » 15 Dic 2013, 22:30

Vlad,deben ser los que aseguran la cinta de algodon al borde superior de la parrilla, creo :roll:
Saludos
Enrique
Socio n° 140
Jeep Ika 1957
GMC CCKW 1942
Avatar de Usuario
ecn1960
 
Mensajes: 3120
Registrado: 11 Jul 2009, 13:35
Ubicación: La Plata - Buenos Aires
Gracias dadas: 15
Gracias recibidas: 83


Volver a Herramientas y equipamientos

¿Quién está conectado?

Usuarios navegando por este Foro: No hay usuarios registrados visitando el Foro y 10 invitados

cron